Programmer

  • You've just added this product to the cart:

    8051 USBASP COMPATIBLE ISP PROGRAMMER

    0 out of 5

    8051 USBASP COMPATIBLE ISP PROGRAMMER

    USBasp is a USB in-circuit programmer for Atmel AVR controllers. It simply consists of an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver, no special USB controller is needed, and thats make it low cost USB programmer.

    280.00
  • You've just added this product to the cart:

    J-LINK USB ARM7, ARM9, ARM11, CORTEX M3 DEBUGGER

    0 out of 5

    J-LINK USB ARM7, ARM9, ARM11, CORTEX M3 DEBUGGER

    Improving the SWD interface circuit, the use of counterfeit JLINK V8 JTAG debug mode can be normal when debugging CORTEX-M3 core chips will not use SWD functionality
    V7 hardware SWD part with the V8 not the same, if forced to switch to SWD mode, JLINK the main chip will be destroyed!

    2,780.00
  • You've just added this product to the cart:

    KEIL ULINK2 USB-JTAG PROGRAMMER & DEBUGGER

    0 out of 5

    KEIL ULINK2 USB-JTAG PROGRAMMER & DEBUGGER

    ULINK2 Keil Debug Adapter connects user PC’s USB port to your target system (via JTAG, SWD, or OCDS) and allows you to program and debug embedded programs on target hardware. ULINK2 may be used for on chip debugging (using on chip JTAG, SWD, or SWV) and flash memory programming (using user configurable flash programming algorithms). Using the ULINK2 adapter together with the Keil µVision IDE/Debugger, user can easily create, download, and test embedded applications on target hardware.

    2,930.00
  • You've just added this product to the cart:

    MSP430-USB-DEBUG-INTERFACE-MSP-FET430UIF-PROGRAMMER-DEBUGGER

    0 out of 5

    MSP430-USB-DEBUG-INTERFACE-MSP-FET430UIF-PROGRAMMER-DEBUGGER

    The MSP-FET430UIF is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required.

    2,900.00
  • You've just added this product to the cart:

    PICKIT3 USB PIC PROGRAMMER/DEBUGGER

    0 out of 5

    PICKIT3 USB PIC PROGRAMMER/DEBUGGER

    PICkit 3 Features
    ⦁ USB (Full speed 12 Mbits/s interface to host PC)
    ⦁ Real-time execution
    ⦁ MPLAB IDE compatible (free copy included)
    ⦁ Built-in over-voltage/short circuit monitor
    ⦁ Firmware upgradeable from PC/web download
    ⦁ Totally enclosed
    ⦁ Supports low voltage to 2.0 volts (2.0v to 6.0v range)
    ⦁ Diagnostic LEDs (power, busy, error)
    ⦁ Read/write program and data memory of microcontroller
    ⦁ Erase of program memory space with verification
    ⦁ Freeze-peripherals at breakpoint
    ⦁ Program up to 512K byte flash with the Programmer-to-Go

    1,800.00
  • You've just added this product to the cart:

    STLINK V2

    0 out of 5

    STLINK V2

    ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board. STM8 applications use the USB full speed interface to communicate with ST Visual Develop (STVD) or ST Visual Program (STVP) software. STM32 applications use the USB full speed interface to communicate with Atollic, IAR, Keil or TASKING integrated development environments.

    930.00
  • You've just added this product to the cart:

    USB LOGIC ANALYZER 24M 8CH DEBUG TOOL

    0 out of 5

    USB LOGIC ANALYZER 24M 8CH DEBUG TOOL

    1.8 channels input;
    2.Logical light indication: a small light indicate CHO electrical level;
    3.Input feature:5PF,100K Ohm;
    4.USB power supply;
    5.Sampling rate can be seted as below:
    24MHz. 16MHz, 12MHz, 8MHz, 4MHz, 2MHz, 1MHz, 500KHz, 250KHz, 200KHz, 100KHz, 50KHz, 25KHz;
    6. Data upload real time,the max of depth of collection is 10T,far from practical need.

    600.00